Recent Content by goldmember

  1. goldmember
    Post

    My 22R

    Finally back on the road.. Still need to get my exhaust dialed in. The setup shown is just a bit loud for my taste. Also its the lowest point on...
    Post by: goldmember, May 3, 2011 in forum: Engine/Drivetrain
  2. goldmember
    Post

    My 22R

    I put a breather/ filter on one and the other (PVC) is running to my carb. Not sure with the side drafts. But I would be interested in knowing the...
    Post by: goldmember, Mar 14, 2011 in forum: Engine/Drivetrain
  3. goldmember
    Post

    My 22R

    What's not good about it?
    Post by: goldmember, Mar 14, 2011 in forum: Engine/Drivetrain
  4. goldmember
    Post

    My 22R

    Nook, were you stalking me today?assume you are referring to the one on the bottom of the block about mid way? That was one of the first things I...
    Post by: goldmember, Mar 6, 2011 in forum: Engine/Drivetrain
  5. goldmember
    Post

    My 22R

    The pump was coated in oil when assembled, everything was, or assembly lube. As for the crank, not sure if the oil passages were cleared, I didn't...
    Post by: goldmember, Mar 6, 2011 in forum: Engine/Drivetrain
  6. goldmember
    Post

    My 22R

    Unfortunitly I didn't get the crank machined or bearings through Engnbldr. I know the bearings were installed properly, they were all cleaned,...
    Post by: goldmember, Mar 6, 2011 in forum: Engine/Drivetrain
  7. goldmember
    Post

    My 22R

    [IMG] Today was a bad day.. New adjuster screws and valve adjustment got the top end sounding nice and quiet.. That helped me to hear a slight...
    Post by: goldmember, Mar 2, 2011 in forum: Engine/Drivetrain
  8. goldmember
    Post

    My 22R

    [IMG] Updated photo.. Let me know if you guys see anything noticeably wrong.. Didn't get a chance to adjust the valves today. Talked with...
    Post by: goldmember, Feb 28, 2011 in forum: Engine/Drivetrain
  9. goldmember
    Post

    My 22R

    Thanks for responses. I timed the motor, it's a little advanced. I don't know where it should be at. Manual said to look at emission sticker under...
    Post by: goldmember, Feb 28, 2011 in forum: Engine/Drivetrain
  10. goldmember
    Thread

    My 22R

    Got my rebuild done and the trucks up and running. It's running a little rough, think the valves need to be adjusted. I put in a RV cam and I'm...
    Thread by: goldmember, Feb 27, 2011, 28 replies, in forum: Engine/Drivetrain
  11. goldmember
    Post

    Carb help: weber content

    I should also mention that I am still running the EGR. So if there are lines I need for that I will need to know. Thanks again
    Post by: goldmember, Feb 20, 2011 in forum: Engine/Drivetrain
  12. goldmember
    Thread

    Carb help: weber content

    Hey guys, So i've done a complete rebuild on my 22r. I am trying to get the last of it buttoned up. I need help with the carb. I have a used...
    Thread by: goldmember, Feb 20, 2011, 3 replies, in forum: Engine/Drivetrain
  13. goldmember
    Post

    80 sr5

    I had the same interior just stock. no cuts in dash or door cards. made new panels and wrapped them in coffee sacks. didn't want to cut up the...
    Post by: goldmember, Jan 21, 2011 in forum: 1976-1983 Build-Up/Project Threads